How many different ways can you mess up a Z axis? 9 so far.

Brutis, my Mini Mendel rework is coming along nicely.  Because all the parts are so small, I can change the design, print off the part and attach to my test frame 20 minutes later, then throw the off part into a vat of Acetone to punish it for it’s insolence.

I have settled on a different form of idler than I have ever seen for the Z axis, hope it works once I cut my belts.  The motor bracket floats on 2 parallel threaded rods, one only attached to the Z base, one that is the frame side bar.  To tighten you will just  tighten 2 wing nuts to move the motor bracket further from the Z base.  It’s a knock off the Mendel Z Leadscrew Base with Motor Belt Tensioner by nicholasclewis, but in 2 parts instead of 1.

I was going a complete different direction with the X trolley, then I saw the rhys-jones’s Mendel Multi Extruder Carriage.  I will have to rework my trolley (that’s why you don’t see it in the pic) because his would add 10+ mm in the inside capacity of the trolley.  Might just be enough to put the extruder on top of the trolley :).  Considering this project is only concerned with making a self replicating printer, if I only have 70 – 80 mm in the Z axis I don’t care as long as it can print all the Mendel parts.

My run of trouble free printing ended.  My hot end started acting up.  Funny thing was Rick over at Makergear got a little perplexed, because he had never seen PEEK have a flowback issue with ABS, and all but demanded I send it too him to let him take a look.  So I sent him my hot end and went to a backup.  There’s something profoundly embarrassing about letting another person look at your nozzel, but I think my constant issues with the Mk4 hot end has finally made him snap (he claims that his hot end is Gremlin proof, we shale see 🙂  He has never seen Gremlins like mine..

Also I just ordered the Power Resistor Heater Block from Makergear (hot end the Nophead way baby!). I personally didn’t like his ceramic heatercore, fire cement and I just don’t get along (which hurts because everyone else who uses them LOVES them… go figure), and the workings for a new hot end (big head nozzel, barrel (turned down on both sides?  never seen that), and a new PEEK thermal barrier.  Wife and kid will be out of town next week, so it’s just me Makerbot, and my 3 half finished Mendels. 

In other news HeeksCAD just released version 0.14.0, and this one is great for our community.  Now STL don’t cause the huge memory leak, or crashing if you hit undo.  I have managed to run it now for 5 hours straight without a single crash, also the colors look a little better.  Dan & his group did a lot of work on this one.

It warms my heart to see Tony Buser has really ran off with my Printable Filament spool over at the RepRap wiki.  I like how he has made the sides stronger, and moved it over the Openscad,  Can’t wait to see his setting under his Mendel!

If you ever get bored and want some good reading, check out the Recent Changes at the RepRap wiki.  They are now up to like 20-30 updates a day, there’s a lot more than just Mendel instructions over there now and days.  Ohh and check out the Wolfstrap, and Eiffel repstraps.  Those projects are quickly becoming the new and improved Mcwire.

That’s all for this week, well besides did you see Adrian’s Ninja electronics set?  I swear I didn’t know it was even possible for a RepRap to be that quite.

Edit  Just saw this. MSC industrial has PFTE tubing CHEAP, like $2-3 a foot cheap.  Lots of other goodies over there also.  Good job tesla893 over at the reprap forum!  Edit further..  PTFE tube bearings for a buck?  God they have EVERYTHING cheap.   I am in heaven.

Advertisements

About spacexula

RepRap, Newspace, Makerbot
This entry was posted in Uncategorized. Bookmark the permalink.

6 Responses to How many different ways can you mess up a Z axis? 9 so far.

  1. About the z tensioner, you mean like this? I had the same idea, but Vik got there first.I like Power resistor heater (and posted pics of mine). It's a bit slower to heat and cool because of the added mass, but that thermal inertia should help if I ever get to printing (I was SO CLOSE when I accidentally tried to run my extruder cold and stripped the threads of my PTFE insulator, and had to order a new PEEK one). I hope you noticed that the aluminum is not pre-drilled (I didn't), but it's surprisingly easy to do if you've already got the metric drill bits and M6x1.0mm tap.If you've got the vertical space, I'd be interested to see how it works with the resistor parallel to the barrel instead of perpendicular. My kit actually came with 3 aluminum blocks, so I might try it myself if I can get my bighead nozzle cleaned up.

  2. Woho! It works! Good, now I feel better about the design, and about 10 points smarter because my mind went the same direction as Vik 🙂 Thanks for pointing that out.

  3. Looking closer his is much more elegant than mine. I will stick with my version till I get a print, and when i start scrubbing mass, I will definitely go his route.

  4. Took a look at that PTFE, Mcmaster's is only 3 cents more per foot.

  5. Rick says:

    oh…i wish old Neil wouldn't post stuff like this. I just couldn't take any more of him going on and on about his hot-end problems…i said send me the dang thing and I'll fix it. Printing with ABS is a solved problem but I never claimed 'gremlin-proof'!!

  6. We built one Mendel with the stock idler but had problems because the part that holds the bearing is too high. We had to add extra washers to keep the belt from binding. For the second and third Mendel we made I looked at several options, including Vik's Z-axis setup, and settled on the one piece design to minimize the needed hardware.I have also had issues with my nozzle recently and am still working on getting a reliable one.Nickhttp://reprapbreeding.blogspot.com/

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s